Retaining wall calculator

A retaining wall 20 ft long and 2 ft high in 12 × 4 in blocks 7 in deep takes 168 blocks with 5% extra, 8 courses of 20 with 2 buried, and 21 caps. Belgard sets it on a 6 in base pad, 0.73 yd³ loose, with 2.27 yd³ of ¾ in stone behind it.

How many blocks for a garden retaining wall, from its length and height and the block’s size, with the caps, the gravel leveling pad under it, the drainage stone behind it and the trench to dig.

Figures checked by Matt Tay (Tay Tzu Haw)

At the lowest end, not counting the cap.

in
in
in

Front to back. Read the sizes off the label: makers often round them.

in
%

More for curves and corners.

$
168 blocks

8 courses of 20, including 5% extra

Courses
8, 2 of them below grade
Wall face
53.3 sq ft, 32 in of block
Caps
21
Leveling pad (¾ in minus base), loose
0.73 yd³ · 1.37 tons, 19 in wide
Drainage stone (¾ in clean)
2.27 yd³ · 2.95 tons, 17 in behind the block
Dig the trench
14 in deep, 19 in wide
4 in perforated drainpipe
20 ft, 1 outlet

The first course sits 6 in or more below grade on a 6 in compacted pad, ordered 25% deeper loose. The stone stops 6 in below the top, under low-permeability soil. Filling the blocks’ cores and gaps takes a little more stone.

Blocks for 10 ft of wall

Height above ground12 × 4 in block, 7 in deep16 × 6 in block, 10 in deep18 × 8 in block, 12 in deep
1 ft50 blocks, 0.61 yd³ stone24 blocks, 0.43 yd³ stone21 blocks, 0.56 yd³ stone
2 ft80 blocks, 1.14 yd³ stone40 blocks, 0.86 yd³ stone28 blocks, 0.8 yd³ stone
3 ft110 blocks, 1.66 yd³ stone56 blocks, 1.3 yd³ stone42 blocks, 1.3 yd³ stone
4 ft140 blocks, 2.19 yd³ stone72 blocks, 1.73 yd³ stone49 blocks, 1.54 yd³ stone

Worked out by the calculator above, with the buried courses and before any extra or caps. The stone is the drainage stone behind the blocks; the leveling pad adds 0.37 yd³ of base per 10 ft under a 7 in block, ordered loose.

The formula

Blocks per course = wall length ÷ block length, rounded upCourses = height ÷ block height + courses buried 6 in, each rounded upPad = length × (block depth + 12 in) × 6 in × 1.25 looseStone = length × the greater of 12 in and (24 in − block depth) × (stack − 6 in)

The pad is ordered loose: Quikrete’s patio guide tamps about 5 in of gravel to 4. The gravel calculator turns any other volume of base or stone into tons, and the paver calculator works out a patio at the foot or top of the wall.

How the wall goes together

Dig a level trench and compact the soil, then the leveling pad, checked level front to back and side to side. Lay the first course on it, buried, starting at the lowest end; on a slope, step the pad up by a block’s height rather than slope the blocks. Fill the blocks’ cores and the gaps between them with ¾ in clean stone, lay the drainpipe behind the first course, and backfill each course with stone directly behind the blocks and compacted soil behind that, 6 in at a time. Pull each block forward to its setback, stagger the joints, and glue the caps on with concrete adhesive. Finish with soil that slopes water away from the top of the wall; the mulch and topsoil calculator works out the topsoil and mulch for a bed behind it. A mortared wall of concrete block is a different build, on a concrete footing: the concrete block calculator counts its blocks and mortar.

Questions people ask

How many retaining wall blocks do I need?

Blocks per course is the wall’s length over the block’s, rounded up; courses are the height over the block’s height, plus the buried ones. A 10 ft wall 2 ft high of 12 × 4 in blocks takes 10 a course and 8 courses, 2 of them below ground: 80 blocks before the extra.

How deep do you bury the first row of a retaining wall?

Belgard buries the first course at least 6 in, on a leveling pad of ¾ in minus base at least 6 in deep after compaction that runs 6 in past the front and back of the block. So the trench goes 6 in below the bottom of the block and is 12 in wider than it. A taller wall’s plans may bury it deeper.

How much gravel goes behind a retaining wall?

Belgard fills at least 12 in behind the back of the block, or 24 in from its face if that is more, with ¾ in clean stone, up to 6 in below the top, where low-permeability soil caps it. A perforated drainpipe runs at the bottom, with an outlet at least every 50 ft. For 10 ft of 2 ft wall in 12 × 4 in blocks, that is 1.14 yd³ of stone.

How tall can a retaining wall be without an engineer?

Belgard recommends a professional engineer design any wall over 4 ft high. Below that, a wall with a load above it (a slope, a drive, a fence or a building), on poor soil, or in tiers can still need geogrid and a design, and some small blocks are rated for walls of only 2 ft. Check the maker’s chart for your block, and your local code.

Sources for the numbers on this page

  1. Belgard: Technical Resource Guide: retaining wall installation (6 in leveling pad, 6 in burial, 12 in of drainage aggregate, engineer over 4 ft) · checked
  2. Vulcan Materials: Construction aggregates calculator: estimated density by rock and product (lb/ft³) · checked
  3. Quikrete: Building a concrete patio — project guide (2×4 forms, stakes at 3 ft, 4 in compacted gravel, ½ in isolation joint) · checked

Corrections and updates are logged on the sources page.