How far apart should control joints be in a concrete slab?

NRMCA puts joints no more than 24 to 36 times the slab’s thickness apart and never over 15 ft: about 10 ft in a 4 in slab, where Michigan’s association says 8 ft and Quikrete 6 to 8. Keep panels no more than 1.5 times as long as wide and cut a quarter of the thickness deep.

Every slab shrinks as it dries, and a slab that shrinks cracks. Control joints decide where. Here is how far apart to put them for the slab’s thickness, how to keep the panels the right shape, how deep to cut and when, from the National Ready Mixed Concrete Association (NRMCA), the Ohio and Michigan concrete associations and the Quikrete project guide, and where they disagree.

Figures checked by Matt Tay (Tay Tzu Haw)

Why a slab needs joints

NRMCA’s CIP 6 sheet puts it simply: joints are pre-planned cracks. Concrete is weak in tension, so when its shrinkage is held back by the ground, the forms or a wall, the stress can exceed its strength and it cracks. A groove cut part-way through makes a weaker line, and the crack forms at the bottom of the groove instead of wandering across the surface. Cracks can’t be prevented entirely, NRMCA says, but joints keep them straight, out of sight and easy to maintain.

There are three kinds. Contraction (control) joints are the grooves this guide is about. Isolation joints separate the slab from anything that holds it still: a house wall, a step, a post or an existing slab. Construction joints are where one day’s pour meets the next.

How far apart: spacing by thickness

The thicker the slab, the farther apart the joints can be. NRMCA gives the rule most guides start from:

Maximum joint spacing = 24 to 36 × slab thickness4 in slab: 96 to 144 in, so 8 to 12 ft (NRMCA: about 10 ft)Never more than 15 ft, whatever the thickness

The state associations are stricter. Ohio’s guidelines tabulate a nominal spacing for each thickness and cap joints at 12 ft. Michigan’s say no more than two times the slab thickness, in feet per inch: 8 ft for a 4 in slab. Quikrete’s sidewalk guide says every 6 to 8 ft in 4 in slab work.

Slab thicknessNRMCA CIP 6 (24–36×, max 15 ft)Ohio (nominal, max 12 ft)Michigan (2×)
3½ in7 to 10½ ft8 ft7 ft
4 in8 to 12 ft10 ft8 ft
5 in10 to 15 ft12 ft10 ft
6 in12 to 15 ft12 ft12 ft

The NRMCA and Michigan columns are their rules worked out for each thickness; Ohio’s are its own table, which gives 12 ft for 5 in or more. For a 6 in slab, 36 times the thickness would be 18 ft, so NRMCA’s 15 ft cap applies. When the sources disagree, the closer spacing is the safer choice.

Keep the panels square

Spacing alone isn’t enough. A long, narrow panel tends to crack across its middle, so every source limits how long a panel can be for its width:

  • NRMCA and Michigan: no panel more than 1.5 times as long as it is wide. NRMCA adds: avoid L-shaped panels.
  • Ohio: panels as square as possible, length no more than 1.25 times the width.

Ohio also asks for contraction joints that are straight and continuous across the slab, not staggered or offset, unless an isolation joint separates the two parts.

The shape rule matters most on walks. A 4 ft wide sidewalk can’t have panels longer than 1.5 × 4 = 6 ft, so it needs a joint at least every 6 ft, even though its thickness alone would allow 8 to 12. That fits Quikrete’s 6 to 8 ft for walks, at the close end.

Worked example: a 12 × 20 ft patio, 4 in thick

Using NRMCA’s 10 ft for a 4 in slab and its 1.5 shape limit:

  1. Spacing first. The 20 ft side needs 20 ÷ 10 = 2 panels; the 12 ft side needs 12 ÷ 10 = 1.2, rounded up to 2. That makes four panels of 10 × 6 ft.
  2. Check the shape. 10 ÷ 6 = 1.67, more than 1.5. Split the long side into 3 instead: panels of 6 ft 8 in × 6 ft, a ratio of 1.11. That passes Ohio’s 1.25 too.
  3. Count the cuts. Three panels along the 20 ft side take 2 joints, each 12 ft long; two panels across the 12 ft side take 1 joint, 20 ft long. That is 3 joints and 44 ft of groove or saw cut.
  4. Check the stricter rules. Michigan’s 8 ft and Quikrete’s 6 to 8 ft for a 4 in slab both accept panels of 6 ft 8 in × 6 ft, so the same layout meets every source here.

The concrete slab calculator gives the concrete for the same patio, and the slab material list counts its control joints for you, keeping every panel no more than 8 ft across, with the isolation strip for any edge against the house.

How deep, and when to cut

A joint has to be deep enough to make the crack choose it. NRMCA asks for a groove at least a quarter of the slab’s thickness deep, and never less than 1 in; Ohio and Michigan say at least a quarter, which is 1 in for a 4 in slab. Quikrete’s guide cuts 1 in joints with a grooving tool.

How the joint is madeWhenSource
Preformed plastic or hardboard stripPressed in before finishingNRMCA CIP 6
Hand-tooled grooveEarly in finishing, rerun later so it doesn’t bond shutNRMCA CIP 6
Early-entry dry-cut saw (at least 1 in deep)1 to 4 hours after finishingNRMCA CIP 6
Conventional saw cut4 to 12 hours after finishingNRMCA CIP 6
Saw cut, typical window8 to 12 hours, varying with weather and mixMichigan

Saw as soon as the edges don’t ravel. NRMCA explains the trade-off: if the blade tears the edges, wait; if you wait too long, sawing gets hard and the slab may crack on its own first. Ohio says the same about delayed sawing. If you hand-tool the joints, Ohio says to cut them before edging. Michigan notes that the window varies with the weather and the mix, so plan the saw around the day’s conditions; see how hot is too hot to pour and how cold is too cold.

Isolation joints and mesh

Where the slab meets the house, a step, a wall, a post or an existing slab, put in an isolation joint before the concrete arrives. Ohio and Michigan both say it must run the full depth of the slab, so the new slab can move up, down and sideways on its own. NRMCA and Quikrete name the usual material: asphalt-impregnated (bituminous) fiber strip, or compressible foam.

Mesh doesn’t replace joints

NRMCA says wire mesh won’t prevent cracking; it tends to keep cracks and joints from opening up. If the slab has mesh, cut every other wire across each contraction joint, or better, stop the mesh at the joint, so the joint can still open and do its work.

For how thick the slab should be in the first place, see concrete slab thickness; for when you can walk or drive on it, see concrete curing time.

Questions people ask

How far apart should control joints be in a 4 inch slab?
NRMCA says about 10 ft (24 to 36 times the thickness, so 8 to 12 ft). Ohio’s table also gives 10 ft; Michigan’s rule gives 8 ft and Quikrete 6 to 8 ft. Use the closer spacing if you’re unsure, and keep each panel no more than 1.5 times as long as it is wide.
How deep should control joints be?
At least a quarter of the slab’s thickness: 1 in for a 4 in slab. NRMCA adds that a joint should never be less than 1 in deep, including early-entry saw cuts.
How soon should you saw cut concrete?
NRMCA gives 4 to 12 hours after finishing for a conventional saw and 1 to 4 hours for an early-entry saw; Michigan says the window is typically 8 to 12 hours. Cut as soon as the blade doesn’t ravel the edges; wait too long and the slab can crack first.
Do you need control joints if the slab has rebar or mesh?
Yes. NRMCA says mesh won’t prevent cracking, only keep cracks tight, and recommends cutting every other wire across contraction joints or stopping the mesh at them.
What is the maximum control joint spacing?
NRMCA caps it at 15 ft for any thickness, and Ohio at 12 ft. Within that, the limit depends on thickness: 24 to 36 times the thickness by NRMCA, 2 ft per inch of thickness by Michigan.

Sources for the numbers on this page

  1. National Ready Mixed Concrete Association: CIP 6 — Joints in concrete slabs on grade (spacing 24 to 36 times the thickness, ¼ depth, panel shape, sawing time) · checked
  2. Ohio Ready Mixed Concrete Association: Guidelines for durable driveways, patios and walks · checked
  3. Michigan Concrete Association: Driveway and sidewalk guidelines · checked
  4. Quikrete: Concrete sidewalks and small slabs — project guide (control joints every 6 to 8 ft, ¼ of the thickness deep) · checked

Corrections and updates are logged on the sources page.