Gravel calculator

A 10 × 10 ft area 4 in deep holds 33.3 ft³ of gravel, or 1.23 cubic yards: 1.6 tons of washed crushed stone at Vulcan Materials’ 96 lb/ft³, or 2.3 tons of crusher run at 138 lb/ft³. A ton of crusher run covers about 43 sq ft at 4 in.

Cubic yards and tons of gravel for a driveway, a base under a slab or patio, a path or a drain, from the area and depth. Pick the stone, since a yard of crusher run weighs nearly half as much again as a yard of washed stone.

Figures checked by Matt Tay (Tay Tzu Haw)

%
$
1.76 tons

1.36 yd³ at 96 lb/ft³, including 10% extra

Cubic yards
1.36
Cubic feet
36.7
Pounds
3,520
Metric
1.04 m³ · 1.6 t

The same product from other rock weighs 90 to 102 lb/ft³: 1.65 to 1.87 tons. Quarries sell by the ton, so ask yours for the density they load by.

Weight and coverage by stone

Materiallb/ft³Tons per yd³sq ft per ton at 4 inUsed for
Crushed stone, washed96 (90–102)1.363#57 and other clean stone: drainage, French drains, under pavers
Crusher run, road base138 (130–160)1.8643Stone with its fines, which packs hard: driveways and slab bases
Pea gravel, river gravel98 (90–102)1.3261Rounded stone: paths, play areas, around posts
Stone dust, screenings113 (110–124)1.5353The fines alone: a bed under pavers or flagstone
Sand110 (100–110)1.4955Paver joints and bedding

Densities from Vulcan Materials’ aggregates calculator: limestone for crushed stone and screenings, sand and gravel for pea gravel and sand. In brackets, the same product from the other rocks it lists, traprock, granite and sandstone among them. A ton is 2,000 lb.

The formula

Cubic yards = length × width × depth (all in feet) ÷ 27Tons = cubic feet × density (lb/ft³) ÷ 2,000

A 10 × 10 ft area 4 in (0.333 ft) deep holds 33.3 ft³, or 1.23 yd³. At 96 lb/ft³ that is 3,200 lb, 1.6 tons; with 10% extra, 1.76 tons.

Loose and compacted depth

A base of crusher run or road base is spread loose and compacted with a plate compactor, and it settles as it’s tamped. Enter the compacted depth you want and add the settling to the extra, or enter the loose depth. The slab material list allows 5 in loose for every 4 in compacted, a quarter more. Washed stone and pea gravel barely compact, so the usual extra covers spreading and uneven ground.

Questions people ask

How many tons of gravel are in a cubic yard?

About 1.3 tons of washed crushed stone, at Vulcan Materials’ 96 lb/ft³ for limestone, and about 1.9 tons of crusher run at 138 lb/ft³. Pea gravel is close to washed stone, 1.3 tons; sand about 1.5.

How much does a ton of gravel cover?

At 4 in deep, a ton of washed stone covers about 63 sq ft and a ton of crusher run about 43 sq ft. At 2 in, double it.

How deep should gravel be under a slab or driveway?

Quikrete’s patio guide puts 4 in of compacted gravel under a patio slab. Gravel tamps down as it’s compacted, so the slab material list orders 5 in loose for that 4 in. A gravel driveway is usually built thicker, in layers of base with a top course of smaller stone. The paver calculator works out the base under pavers (and the paver patio material list the whole patio), the retaining wall calculator the pad and drainage stone for a block wall, and the mulch and topsoil calculator what goes in the beds.

Should I order by the yard or the ton?

Order the way your supplier sells: quarries and most yards weigh their trucks and sell by the ton; some landscape yards sell by the yard. The calculator gives both, and the density to ask about if your supplier’s differs.

Sources for the numbers on this page

  1. Vulcan Materials: Construction aggregates calculator: estimated density by rock and product (lb/ft³) · checked
  2. Quikrete: Building a concrete patio — project guide (2×4 forms, stakes at 3 ft, 4 in compacted gravel, ½ in isolation joint) · checked

Corrections and updates are logged on the sources page.